Carefully slide the camshaft out of the engine block, using caution to avoid any damage to the camshaft bearings. Position the drain pan accordingly and move it more directly beneath the drain plug as the flow slows to a trickle. Raise the vehicle and support it safely. Remove the upper and lower intake manifolds. © 2004 Thomson Delmar Learning.
View of the electrical connections on the back of the cluster To install: Connect the electrical wire harness plugs and install the instrument cluster. Align the groove with the crankshaft keyway and install the damper. These devices are composed of two separate components. The square panel type retains the housing cover by bolts or, on later models, bail clips. Instead, a filler plug is located in the side of the housing or in the side of the cover , at a level just barely above the level to which fluid should fill the housing. Remove the camshaft sprocket bolt and sprocket retaining key. When the proper tension is attained, tighten the mounting bolts.
Remove the power steering pump and bracket assembly. If necessary, unbolt the chain guide attaching bolts. Remove the upper radiator and heater supply hoses from intake manifold. The emission system heats up the engine compartment and exhaust system, which can start a fire. Install the heater core access cover to the plenum assembly and secure with four screws. Punch the holes on opposite sides of the crankshaft and just above the bearing cap to cylinder block split line. If the left cylinder head is being removed: Remove the accessory drive belt.
Furthermore, in the same year, Ford of Britain and Ford of Germany launched the first generation Ford Transit. Submerge the pump in clean engine oil to prime it. But whether or not you decide to replace it, you would be wise to check it periodically to make sure it has not become damaged or worn. You will need these specialized tools to unfasten the fan clutch nut If necessary, remove the air cleaner outlet tube. Install the fuel supply and return line assembly. Remove the mounting nuts, then separate the sensor from the mounting bracket.
A complete printed circuit, consisting of conductors, insulating material and connectors for lamps or other components is called a printed circuit board. The wiper arm can now be removed from the shaft without the use of any tools. Markings on the heads of most bolts will help determine the proper strength of the fastener. Remove the pushrods, keeping them in order so they may be installed in their original locations. Ford strongly recommends that drivers use extreme caution when using any device that may take their focus off the road.
I looked on ebay and there were none. Use only fluid that meets Ford specifications. Apply 50W engine oil to both ends of the pushrods. Never pull on the wire Using compressed air, blow any water or debris from the spark plug well to assure that no harmful contaminants are allowed to enter the combustion chamber when the spark plug is removed. Remove the drive belt tensioner. When selecting tires, pay attention to the original size as marked on the tire. Connect the hydraulic clutch master cylinder pushrod to the clutch pedal.
Note the rear support and the bracket that it attaches to Click to enlarge Disconnect the negative battery cable. Remove the wheel and tire assembly. Connect the negative battery cable. Check the center bearing support for wear by rotating the outer area while holding the coupling shaft. To test an injector, detach the engine wiring harness connector from it. Disconnect the wire from the switch.
Most areas require extra marker lights for overwide trailers. You may want to cover the differential gears using a rag or piece of plastic to prevent contaminating them with dirt or pieces of the old gasket. A low voltage signal from the sensor indicates too much oxygen in the exhaust lean condition and, conversely, a high voltage signal indicates too little oxygen in the exhaust rich condition. The fluid level should be up to the fill hole. Use a rag to shield your fingers from the heat. If the spacers were installed under the center bearing be sure to reinstall them. Airbags offer greater protection when used with safety belts.
Remove the engine from the vehicle. Use a quality air pressure gauge Click to enlarge Common tire wear patterns and causes Click to enlarge A plate or sticker is normally provided somewhere in the vehicle door post, hood, tailgate or trunk lid which shows the proper pressure for the tires. Remove the air conditioning compressor. If equipped with an automatic transmission, disconnect the transmission cooling lines from the bottom of the radiator. For additional information, see the Global Shipping Program This amount includes applicable customs duties, taxes, brokerage and other fees.
This is normal and should be no reason for concern. Install the alternator adjusting arm and brace. Check that the timing marks are aligned on the camshaft and crankshaft pulleys. When raising the vehicle on a hoist, position the front end adapters under the center of the lower suspension arm or the spring supports as near to the wheels as practical. Loosen the water pump pulley attaching bolts. If it is already loose, now would be a good time to remove it and check the condition of the gasket underneath. Ford Motor Company shall not be responsible for any such programming changes.